Capture zoom

Hover

Capture
Full Screen

DJI Phantom 2 + H3-3D Combo

114,234

Fun flying by itself or even better with a GoPro to record the action
The latest Phantom 2 comes with the new remote controller, new propulsion system and new compass
For Phantom 2 + H4-3D: Zenmuse H4-3D gimbal (works with the GoPro Hero4 Black camera) is included for extreme camera stability and silky smooth video recording
For Phantom 2 + H3-3D: Zenmuse H3-3D gimbal (works with the GoPro Hero[3 or 3+] camera) is included for extreme camera stability and silky smooth video recording
Note: GoPro camera is NOT included

Compare
  Ask a Question

Description

DJI Phantom 2 V.2 + Zenmuse H3-3D + gopro Black

What’s news:

The upgraded remote control comes with new features, including a gimbal control dial, a built-in LiPo battery, and battery level LED indicators.

New Features:
1. Left Dial: Turn the dial to the right, and the camera will shift to point upwards. Turn the dial to the left, and the camera will shift to point downwards. The camera will keep its current position if the dial is static.

2. Built-in LiPo Battery: The remote control includes a rechargeable LiPo battery with a capacity of 2000mAh. You can monitor the current battery level using the LED indicators on the front panel of the remote control as the figure shown

3. Charging the Remote Control: Charge the remote control’s battery by using the included micro-USB cable. The LED indicators will display solid red when charging is in progress. The LED indicators will display solid green when the battery is fully charged.

4. Throttle Lock: Pull down the throttle stick to descend. The stick will lock into place and the aircraft will descend steadily. Push the throttle stick upward to release the throttle lock.
5. Trainer Port: Connect the remote control to the computer via the trainer port to run the simulation application

The new 2312 motor adopts a pioneering stator winding structure, which not only makes it tidy and neat but also increases slot wire embedding degree and offers improved heat dissipation. With its impact-resistant bearings, the system is more durable than ever before. The electromagnetic design, tailored for the DJI Phantom, has effectively improved the output power, and when used with the new 9450 propellers and new ESC (electronic speed controller), your whole propulsion system can provide 200g/axis more maximum output thrust when using a 3S LiPo battery. Additionally, this new propulsion system allows you to load more equipment on your Phantom without sacrificing flight time, offering you a better flight experience.

New Features:
1. The double layer, single wire stator technology increases slot wire embedding degree and improves heat dissipation. Also, the single wire stator design improves motor efficiency and its ability to withstand a larger current, ensuring consistency in the motor’s performance.
2. The new bearings, with higher durability and ability to withstand greater impacts, are used to avoid damage in the event of an accident, greatly reducing maintenance costs.
3. New insulation coating powder is used to improve the stator voltage capacity, ensuring the working life and stability of the motor.
4. The electromagnetic design and lightweight structure, customized for the DJI Phantom, have increased maximum output power by nearly 25% without adding extra weight.
5. The new propeller adopts a 4.5-inch pitch, which when used with the 2312 motor can provide an extra 200g/axis of output thrust, giving you both power and flexibility. Furthermore, your Phantom’s flight time is not reduced, because of the increased aerodynamic performance and motor efficiency.

The Phantom 2 will be available in two versions

WITH Zenmuse (price 749 EUR) – our article number 700006
The Spirit of Flight
The Phantom 2 is an evolution of the Phantom. It features the same compact and highly integrated design but comes with FPV flying and Aerial Photography support right out of the box. Hardware mountings and software tuning are all carried out prior to delivery, meaning with rotors attached, a charged battery, and transmitter batteries available it can fly immediately. Additional features include a higher payload, a built-in intelligent battery, H3-2D gimbal support, and other functions.

Key Features:
Can-bus Expansion Module for Function Expansion Functions of the Phantom 2 can be expanded through its Can-bus module, which can be used for IOSDor 2.4 G Bluetooth Datalink.
Customized H3-2D Gimbal Support
A customized H3-2D gimbal, designed for easy assembly and connection is available for the Phantom 2. Its stability ensures high-quality footage and the camera’s pitch can be controlled from the transmitter, allowing pilots to be more creative.

Key Features:
Can-bus Expansion Module for Function Expansion Functions of the Phantom 2 can be expanded through its Can-bus module, which can be used for IOSDor 2.4 G Bluetooth Datalink.
Customized H3-2D Gimbal Support
A customized H3-2D gimbal, designed for easy assembly and connection is available for the Phantom 2. Its stability ensures high-quality footage and the camera’s pitch can be controlled from the transmitter, allowing pilots to be more creative.

Easy upgrade to FPV
AV output and video-downlink power cables already installed, ready for an upgrade.
Precision Flight and Stable Hovering
Integrated GPS auto-pilot system offers position holding, altitude lock, and stable hovering allows attention to be focused on shooting.
25min Flight Time & Intelligent Battery
High capacity, high performance 5200mAh intelligent Lithium Polymer battery offers up to 25 minutes of flight time, with battery capacity data, overcharge/discharge protection, and maintenance reminders for greater reliability.

Auto Return-to-Home & Landing
If the Phantom 2 and its controller disconnect during flight for any reason, the Naza-M autopilot system’s failsafe protection will come to the rescue. Outputs of all command sticks on the controller will go to the center position and if the signal is good enough the Phantom 2 will return to home and land automatically. You can also program a One Key Go Home function through the Assistant software.
Intelligent Orientation Control (IOC)
In traditional multirotor flight, the forward is tied to the direction of the nose. Using IOC, it flight is much simpler. In Course Lock mode, the forward direction is will always be the direction the nose faced at takeoff, while in Home Lock mode forward takes the Phantom 2 back to where it took off. Users can adjust these settings as they please.

Advanced Power Management Power consumption has been improved by a custom power management system that monitors power capacity and voltage. Low power is indicated by the LED. If power drops below safe levels, the Phantom 2 will land automatically during low battery levels.

Easy Battery Replacement Integrated battery compartment allows for near-instant battery changes. Self-tightening Propeller Install propellers without worry using self-tightening propellers that only install in the right place. These will also tighten during flight, enhancing safety. All propellers have been carefully and dynamically balanced to eliminate the jello effect.

DJI Zenmuse H3-3D for GoPro 3/GoPro 3+

Features
3-axis high-performance gimbal
3-axis GoPro stabilization, high precision control (within ±0.08°)
The 3-axis Zenmuse H3-3D Gimbal is another milestone in gimbal innovation. Designed for the GoPro Hero3 and Hero3+, it is a high-precision gimbal
offering high stability, lightweight, and plug and plays simplicity. It is ideal for a range of applications, from film and TV to cinematography.

Create astonishing aerials, compatible with Phantom 2 and Flame Wheel

Smooth aerial creativity
Aluminum alloy material. Strong, lightweight, easy to install, plug and play. Free
Hardware mounting and software tuning.
Compatible with DJI flight control systems
• Multirotor (currently support) – WooKong-M, NAZA-M V1, NAZA-M V2, Phantom 2
• Heli (will support) – Ace One, WooKong-H, NAZA-H
• NAZA-M LITE not supported
Notice: NAZA-M V1 and Phantom users must use NAZA-M V2 PMU

Part of the Zenmuse family
The H3-3D gimbal inherits the core algorithms of the Zenmuse professional series and
is powered by advanced algorithms, high precision sensors, and brushless motors. This
means that the DJI Zenmuse H3-3D gimbal provides pixel-level stabilization.

Independent IMU
The independent high-precision IMU module is easy to install a unit that provides
precise attitude data while a closed-loop control gives improved control accuracy.

Online Upgrade
Functionalities can be easily expanded through firmware upgrades.

Specifications
Peripheral
Supported Camera: GoPro Hero 3/ Hero 3+ (Black and Silver)
GCU Input Power: 3S~6S LiPo(12V~26V)
Assistant Software System Requirement: Windows XP SP3; Windows 7; Windows 8
Mechanical & Electrical
Gimbal Operating Current Static current: 400mA (@12V); Dynamic current: 600mA (@12V)
Gimbal Input Power: 3S~6S(12V ~26V)
Operating Temperature: -10°C ~ 50°C
Gimbal Weight: 168g(without GoPro3 camera)
Gimbal Dimensions (With Damping Unit): 99.5mm ×85.5mm ×92.75mm
GCU Weight: 22g
GCU Dimension: 42 mm X32 mm X9.3 mm
Performance
Controlled Angle Accuracy: ±0.08°
Maximum Controlled Rotation Speed: Tilt axis: ±130°/s
Controlled Rotation Range: Tilt axis control: -130~+45°
Regulatory Approvals
FCC(USA): Yes CE(EU): Yes RoHS(EU): Yes

Model H3-3D H3-2D
Function
3-axis(Tilt, Roll, Pan) stabilization 2-axis(Tilt, Roll)stabilization
Tilt control
Accuracy:0.08°
Camera support: GoPro Hero 3/Hero 3+
Flight controller support: WKM /NAZA-M /NAZA-M V2 /PHANTOM
Hardware
3-axis mechanical structure 2-axis mechanical structure
Stronger motor shaft Normal
Gimbal weight: 168g Gimbal weight: 157g
Standard H3-3D VS Customized H3-3D for Phantom 2
The standard H3-3Dfeatures is an independent GCU. Customized H3-3D for Phantom 2 doesn’t have one.
H3-3D Mounting Adapter

We also recommend
GRAUPNER ELECTRO PROP 8″x5″ right
GRAUPNER ELECTRO PROP 8″x5″ right
5.10 € *
Delivery weight: 100 g

GRAUPNER ELECTRO PROP 8″x5″ LEFT
GRAUPNER ELECTRO PROP 8″x5″ LEFT
5.10 € *
Delivery weight: 100 g

7-8 inch FPV Monitor Mount to Futaba/JR/WFLY Transmitters
7-8 inch FPV Monitor Mount to Futaba/JR/WFLY Transmitters
9.90 € *
Delivery weight: 100 g

Female XT60 connectors original
Female XT60 connectors original
1.30 € *
Delivery weight: 20 g

Lipo 2200mAh Phantom DJI FC40 / F330 dji 330
Lipo 2200mAh Phantom DJI FC40 / F330 dji 330
19.90 € *
Delivery weight: 200 g
Flight Case for phantom dji F 330
Flight Case for phantom dji F 330
49.00 € *
Delivery weight: 15 kg

Gimbal- 2-axis stabilized GoPro II & III mount. for phantom
Gimbal- 2-axis stabilized GoPro II & III mount. for phantom
42.00 € *
Delivery weight: 100 g
* The price includes VAT
Browse these categories as well: DJI Phantom 2, MultiRotor for Gopro

Reviews

There are no reviews yet.

Be the first to review “DJI Phantom 2 + H3-3D Combo”

Your email address will not be published.

No more offers for this product!

General Enquiries

There are no enquiries yet.